- Force sensor inside the flange The six-axis sensor measures force and torque where the tool meets the part, with no external sensor to mount or cable.
- Factory calibrated The sensor needs no further calibration or configuration before force-controlled work.
- Tool ports stay free Force control leaves the flange's two DI, two DO and two AI (shared with RS485) for the gripper or camera.
- Constant force on curved parts Dobot rates contact force following at ±3 N on complex surfaces, for even polishing, sanding and deburring.
- Light hand guiding A drag start force under 2 N and a press-to-drag button make teaching by hand quick and precise.
- Sensitive collision detection The robot detects collisions from 1 N and stops, with a ring status light on the flange.
Descripción
The CR5AF is Dobot's 5 kg CRA arm with a six-axis force and torque sensor built into the flange and calibrated at the factory. It is made for work where position alone is not enough: polishing a curved panel, sanding, pressing a connector home or fitting a shaft, where the robot has to feel how hard it is pushing and correct as it goes.
Because the sensor sits inside the flange, there is no adapter plate, no extra length at the tool and no external sensor cable. Force control does not use the tool-side RS485 or I/O, so electric grippers and smart cameras connect as usual. Dobot gives the sensor a range of 150 N for Fx, Fy and Fz and 15 N·m for Mx, My and Mz, with 1% F.S. accuracy and 500% F.S. overload.
Hand guiding is light. The whole flange is a drag zone with a start force under 2 N and a press-to-drag button, and orientation can be locked to teach precise paths. Dobot rates constant-force following at ±3 N on complex surfaces and collision detection from 1 N, and a ring light on the flange shows the robot's state.
The arm carries 5 kg across a 900 mm working radius, repeats to ±0.02 mm, weighs 25.5 kg and draws 150 W. It is rated IP54 and mounts upright. For wet or oily cells the IP68 CR5AP is the better match, and for close work beside people the CR5AS adds SafeSkin.
Key Capabilities
- Force sensor inside the flange: The six-axis sensor measures force and torque where the tool meets the part, with no external sensor to mount or cable.
- Factory calibrated: The sensor needs no further calibration or configuration before force-controlled work.
- Tool ports stay free: Force control leaves the flange's two DI, two DO and two AI (shared with RS485) for the gripper or camera.
- Constant force on curved parts: Dobot rates contact force following at ±3 N on complex surfaces, for even polishing, sanding and deburring.
- Light hand guiding: A drag start force under 2 N and a press-to-drag button make teaching by hand quick and precise.
- Sensitive collision detection: The robot detects collisions from 1 N and stops, with a ring status light on the flange.
Buying through Robotix Market
This unit is sourced new through established distribution channels and ships worldwide with the manufacturer warranty. Technical support is coordinated with the manufacturer's own service network. Deployment scope, configuration, and commissioning responsibilities are agreed as part of the quotation, and on-site installation is not included in the product price.
Características
Especificaciones
| Brand | Dobot |
|---|---|
| Model | CR5AF (CRAF series) |
| Dobot Part Number | 1200000187-Z |
| Product Type | Six-axis collaborative robot arm with integrated flange force sensor |
| Degrees of Freedom | 6 |
| Payload | 5 kg |
| Working Radius | 900 mm |
| Repeatability | ±0.02 mm |
| Maximum Linear Speed | 2 m/s |
| Joint Ranges | J1, J2, J4, J5, J6 ±360°; J3 ±160° |
| Maximum Joint Speed | J1 to J3 180°/s; J4 to J6 223°/s |
| End Effector I/O | 2 DI, 2 DO, 2 AI (shared with RS485) |
| Weight | 25.5 kg |
| Power Consumption | 150 W |
| Cable Length | 5 m |
| Mounting | Upright |
| Ingress Protection | IP54 |
| Operating Temperature | 0 to 50 °C |
| Force Sensor | Six-axis, integrated in the flange, factory calibrated |
| Force Sensor Range | Fx/Fy/Fz 150 N; Mx/My/Mz 15 N·m |
| Force Sensor Accuracy | 1% F.S. |
| Force Sensor Overload | 500% F.S. |
| Drag Start Force | Under 2 N |
| Constant Force Accuracy | ±3 N on complex surfaces |
| Collision Detection | From 1 N |
| What's in the Box | Confirm at quote |
Sectores
Preguntas frecuentes
It is the same 5 kg, 900 mm arm with a six-axis force and torque sensor integrated in the flange, a ring status light and press-to-drag control.
No. Dobot calibrates it at the factory.
Up to 150 N along each axis and 15 N·m around each axis, with 1% F.S. accuracy and 500% F.S. overload protection. Check that your process forces sit well inside that range.
Yes. Force control does not occupy the tool-side RS485 or I/O.
The arm is IP54. For coolant, heavy dust or washdown, the IP68 CR5AP is the better choice.
The Dobot CR5AF Force-Sensing Collaborative Robot is priced at $17,600 in your market. For volume or project orders, contact us for a business quote.
Vistos recientemente
Aún no has visto ningún producto.
